Raise the method of speed of cut of silk of don't go yet of line cut machine tool

  • Time:
  • Click:152
  • source:EAMOM CNC Machining
The article introduced to be in Er of Swiss summer rice (a few practical methods that line cut raises to machine speed on machine tool of cut of silk thread of Robofi1290P) don't go yet. The mould is made in a the discretion of electric treatment efficiency is the influence mould cycle that make main factor. Cut of silk thread of don't go yet should achieve good dimension precision and exterior surface roughness, want to adopt cut for many times normally, and among them cut rate is the slowest is cut the first, namely rough machining, should raising key of line cut speed so is the rate that raises cut the first times. Below with respect to Swiss Xia Mier (a few practical methods that introduction of machine tool of cut of silk thread of Robofi1290P) don't go yet raises line cut to machine speed. 1 assure to go up, next high-pressured water jobs are good nozzle of a powerful person of water of the high-pressured pump in checking return, high pressure, bypass water a powerful person, fluctuation, fluctuation nozzle and conduit ensure any jamming and did not divulge a phenomenon. When treatment, make fluctuation nozzle parts as far as possible surface of fluctuation of workpiece of press close to (the attention prevents collision of nozzle and clamping apparatus, beam) , such, ability of high-pressured gush water works effectively. In rough machining, high-pressured water position is good, ability makes insulation maintains between electrode silk and workpiece, fast rinse out of among them electric corrode content, reduce discharge and short circuit phenomenon 2 times, cut rate can rise. 2 assure to go up nose is electric piece with next nose the lubricant water of electric conduction annulus works nozzle of a powerful person of the circular pump in good examination loop, lubricant water, fluctuation reach conduit to want unobstructed, lubricant water must sufficient, lest electrode silk cut arrives go up nose is electric piece with next nose electric conduction annulus, reduce cut efficiency. The 3 ion that assure electrolyte spend the electrolyte that here says is to go ionic water, its insulating properties is good, be helpful for discharge treatment. Spend with ion normally (namely electrolyte electrical conductivity) will measure ionic concentration. General, in user parameter menu set ion is spent for 15µs/cm. In treatment, if the sensor in clean cistern measures gotten ion actually to spend,be more than set to be worth 15µs/cm ± 2µs/cm, should change ionic bottle goes mediumly ionic colophony. If changed,ionic bottle goes mediumly after ionic colophony, still cannot spend ion fall, should check go ionic loop. The 4 quality that assure to use electrode silk use the electrode silk of different material to machine a spare parts, machining speed is different. Machine for example when be the same as material workpiece, the treatment rate that includes zincic silk XS25 to compare brass silk LS25 wants fast. The electrode silk that uses same data machines a spare parts, if electrode silk character is different, treatment speed also will differ. The consistency of the uniformity that electrode silk character points to material is qualitative, diameter and exterior surface roughness. 5 make sure discharge loop link is nice make sure cable link is nice, include: ?  of rare ⑾ salary returns  of herd of busy of Hui of ǖ of Xiao of ぷ of sweat of cherry of  of Hui busy herd to imprint ⑾ of H Quan  embraces Hui to sweep past river of Deng of 〗 of ε of  of the  that promote what to wake to  ⒆ of alliance of wholesale   especially  of コ  wholesale scrupulously and respectfully busy of Hui of ＜ Hu Lv, line cut machine tool can give out automatically when treatment discharge parameter, if to raise rough machining rate, can adjust parameter of the following discharge appropriately: Reduce servo fiducial and average voltage: Increase pulse breadth: Increase short pulse time, notice short pulse time wants to be less than pulse width: Increase discharge frequency. Besides, still have those who assure silk of carry of carry silk orgnaization is smooth, workpiece outfit is placed and rise cut the position to wait for a method correctly. What rough machining goes after is efficiency, what finish machining goes after is precision and requirement of exterior surface roughness. Sometimes, finish machining falls in the premise that assures precision and exterior surface roughness, also can raise treatment rate appropriately, if reduce the cut surplus of finish machining,wait. CNC Milling CNC Machining