What new technology did treatment of silk of don't go yet have again?

8μm left and right sides, it is the ply of 100mm what is more,the rather that more. As the pioneer of production technology, mu Ye has history of long line cut research and development, its technology carries world van from beginning to end. The series of U of machine tool of silk of homebred don't go yet that herd tough firm rolls out used a series of newest technologies, processability can have rise revolutionarily. Of machine tool of silk of don't go yet of series of U of Mu Ye of 　 of U3/6 of machine tool of cut of line of numerical control of herd wild high accuracy exceed cut technology, cut below standard treatment condition repair 2 can achieve Ra0.

The exterior surface roughness of 4μm. relatively the treatment mode at the tradition, realizing surface roughness of exceedingly good surface while decreased to write knife number, with the line fewer, treatment is quicker. 1) rolled steel is cut repair 2 can amount to Ra0.

4μm 　 　 2) hard alloy is cut repair 2 can amount to Ra0.

34μm 　 　 3) even if expensive work, still have 　 of very good 　 of 　 of face coarseness 　 series rolled steel cuts Mu Ye U to repair 2 achieved appearances material of surface roughness workpiece: SKD11 steel uses line means: Φ0.

Ply of material of 25mm brass line: Surface roughness of 80mm 　 surface: Rz3μm (Ra0.

　 of 4μm) 　 　 at the same time, mu Ye's distinctive GS-Cut technology, can assure the linearity of deeper work, in be more than the work with deep 300mm to go up, only the common difference that 1 knife can realize 5μm. This technology is in rough machining can cut goes out straighter, more the work with standard essence, make finish machining goes up from workpiece the material that remove is fewer, can obtain taller precision. The machine tool of silk of don't go yet of series of linearity 　 U that 1 times treatment can assure deeper work still has the following and main characteristic: 1) structure of machinery of type of cascade of structure of machinery of tall tigidity, tall stability, each axes yuan between each other noninterference; Workbench is fixed do not move, axial motion does not suffer the effect of workpiece weight; Double end of ball silk lever is propped up, ensure the stability of transmission. 2) fluctuation treatment fluid controls fluctuation to machine fluid to be supplied by different water pump independently; Pour water up and down, discharge, pressure is controlled independently; Digitlization controls flow; Can control treatment hydraulic pressure outstandingly, obtain good appearance precision. 3) direct technical fluctuation guider ensures beforehand the perpendicular position of the line, verticality won't get the influence of loss of electric conduction piece; Diamond V guider props up line impaction electric conduction piece, make sure electric result is favorable. 4) H.

E.

A.

T.

Technology (high-energy application technology) two side of 　 are far from technology of high speed cut, good linearity and paragraph poor dimension, treatment efficiency promotes 51% , cost is reduced 30% . 5) the treatment parameter that conditional database machine tool configures a variety of material, the steel besides convention, nonferrous metal, exceed hard data, still configured the treatment parameter that is aimed at the aviation material, material such as semiconductor PCD and SIC. 6) Hyperi controller intelligence is changed, setting of menu of simplification flow type; Gesticulation control, good and interactive sex; Intelligence controls Dr. —E; Information feedbacks, the picture is auxiliary; Coach constantly, manual joins automatically. 7) safeguard handy electric conduction piece 10 seconds conversion; Filter noumenon and water are detached; Machine tool education of synchronism of real time video, dimension is protected without care. Silk of don't go yet of series of wild U of new generation herd can satisfy Mu Ye large and medium-sized the mould is made, the disparate industry such as inn of exact pattern treatment and component treatment is extensive to treatment and slashing requirement, provide stronger manufacturing competition ability for the client. CNC Milling CNC Machining